Study of the performance of a coolant mixed with an Al2O3/SiC nanomaterial in an engine radiator

One of the important components of a car to control the temperature of a car's engine is the radiator. To increase the heat absorption capacity of the coolant/fluid used in the radiator with minimum pumping power, innovative fluids called nanofluids have become the main area of research these days. Therefore, with the development of new technologies in the field of “nano-materials” and “nano-fluids,” the physical and chemical properties of coolant/fluid can be improved which in turn improves the radiator and engine efficiency, and reduces radiator weight and size. In this article, the heat transfer by forced convection in nanofluids based on Al₂O₃ and SiC was studied experimentally and compared to that of base fluid in an automotive radiator. The nanofluid is mixed with ethylene glycol and the fluid is prepared by the sonication method. The nanofluids were prepared by varying the nanomaterials and the amounts of nanomaterials in the base fluid and their heat transfer performance in the radiator was analyzed using ANSYS FLUENT software. Approximately 15% and 12% increase in radiator efficiency by using Al₂O₃ mixed nanofluid and SiC mixed nanofluid, respectively.     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9％ ～5.4％.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3％的系统脱硫效率整体高于含湿量为5％和4％的样品,最大值达93.56％.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3％的循环脱硫灰较含湿量为5％的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5％样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaS03干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

Using the past to contextualize anthropogenic impacts on the present and future distribution of an endemic Caribbean mammal

Island species are difficult to conserve because they face the synergy of climate change, invasive species, deforestation, and increasing human population densities in areas where land mass is shrinking. The Caribbean island of Hispaniola presents particular challenges because of geopolitical complexities that span 2 countries and hinder coordinated management of species across the island. We employed species distribution modeling to evaluate the impacts of climatic change and anthropogenic activities on the distribution of an endemic mammal of conservation concern, the Hispaniolan solenodon (Solenodon paradoxus). We aggregated occurrence points for this poorly known species for the Last Glacial Maximum (LGM) and the present (1975–2016) based on museum collections, online biodiversity databases, and new field surveys. We quantified degree of overlap between periods and scenarios with Schoener's D. Through a conservation paleobiology lens, we found that over time humans played an increasing role in shaping the distribution of S. paradoxus, thus, providing a foundation for developing conservation strategies on appropriate spatiotemporal scales. Human population density was the single most important predictor of S. paradoxus occurrence. Densities >166 people/km² corresponded to a near-zero probability of occurrence. Models that accounted for climate but not anthropogenic variables falsely identified suitable habitat in Haiti, where on-the-ground surveys confirm habitat is unavailable. Climate-only models also significantly overestimated the potential for habitat connectivity between isolated populations. Our work highlights that alternative fates for S. paradoxus in the Anthropocene exist across the political border between the Dominican Republic and Haiti due to the fundamentally different economic and political realities of each country. Relationships in the fossil record confirm that Hispaniola's sociopolitical boundary is not biologically significant but instead represents one imposed on the island's fauna in the past 500 years by colonial activity. Our approach reveals how a paleontological perspective can contribute to concrete management insights.     

Unintentional non-traffic injury and fatal events: Threats to children in and around vehicles

Objective: There have been substantial reductions in motor vehicle crash–related child fatalities due to advances in legislation, public safety campaigns, and engineering. Less is known about non-traffic injuries and fatalities to children in and around motor vehicles. The objective of this study was to describe the frequency of various non-traffic incidents, injuries, and fatalities to children using a unique surveillance system and database.

Methods: Instances of non-traffic injuries and fatalities in the United States to children 0–14 years were tracked from January 1990 to December 2014 using a compilation of sources including media reports, individual accounts from families of affected children, medical examiner reports, police reports, child death review teams, coroner reports, medical professionals, legal professionals, and other various modes of publication.

Results: Over the 25-year period, there were at least 11,759 events resulting in 3,396 deaths. The median age of the affected child was 3.7 years. The incident types included 3,115 children unattended in hot vehicles resulting in 729 deaths, 2,251 backovers resulting in 1,232 deaths, 1,439 frontovers resulting in 692 deaths, 777 vehicles knocked into motion resulting in 227 deaths, 415 underage drivers resulting in 203 deaths, 172 power window incidents resulting in 61 deaths, 134 falls resulting in 54 deaths, 79 fires resulting in 41 deaths, and 3,377 other incidents resulting in 157 deaths.

Conclusions: Non-traffic injuries and fatalities present an important threat to the safety and lives of very young children. Future efforts should consider complementary surveillance mechanisms to systematically and comprehensively capture all non-traffic incidents. Continued education, engineering modifications, advocacy, and legislation can help continue to prevent these incidents and must be incorporated in overall child vehicle safety initiatives.     

Heat dissipation characteristic in the intake grille and radiator of a fuel cell vehicle

ABSTRACT

In this study, a three-dimension (3D) computational model was proposed to investigate the flow and heat transfer characteristics of the intake grilles of two different fuel cell vehicles. The models of the intake grilles were constructed according to the actual sizes of two vehicles, namely, Roewe 950 and Toyota Mirai, considering the heat dissipation unit to simplify the heat transfer model of the vehicle. The results showed that relative to Roewe 950, Mirai intake air flow rate was approximately 10% higher, the heat transfer capacity was approximately 7% higher, and the intake grille area was larger. The coolant outlet temperature of Mirai was lower than that of Roewe 950, which was beneficial for the long term and stable operation of a fuel cell. This comparative study provided guidance for the intake grille and radiator design of fuel cell vehicles. The only difference between fuel cell vehicles on the market and conventional vehicles was that in the former, the internal combustion engine was replaced with a fuel cell stack, which had insufficient heat transfer capacity because of the reducing temperature difference. Increasing the intake grille area and the heat exchange capacity of the radiator were the key issues for the development of fuel cell vehicles. In this study, an optimal window opening angle of the radiator fin of 23° provided a maximal heat transfer coefficient.     

Characteristics of stable biodiesel emulsion fuel with the aid of lipophilic surfactant,polyglycerol polyricinoleate (PGPR)

ABSTRACT

Biodiesel emulsion fuel is reported as one of the most feasible options capable of generating lower NOx emission than that from fossil fuels. However, oil and water in the emulsion fuel are easily separated and unstable. The aim of the present study is to consider the production and stability of biodiesel emulsion fuel by using tetraglycerin ester (CR-310), i.e., one of lipophilic surfactant, polyglycerol polyricinoleate (PGPR) and biodiesel, i.e., Waste cooking Oil Methyl Ester (WOME) produced based on waste cooking oil. The corresponding heat rate, water content, and viscosity are measured. Emphasis is placed on the effects of water content and surfactant on biodiesel emulsions. It is found that: (i) stable emulsion fuel is obtained by adding at least 2.0% of CR-310 and is maintained over 1 month, (ii) there is no effect of water content on stable emulsion fuel if CR-310 is used over 2.0%, and (iii) the viscosity of emulsion fuels is higher than that of the biodiesel fuel and is gradually increased with an increase in the water content.     

海岛居民环境友好行为及其影响因素研究--以长岛县为例

海岛是海洋生态系统的重要组成部分,保护海岛生态环境是推进海洋生态文明建设、保护海洋生态环境的重要方面。海岛居民是保护海岛生态环境的主体之一,研究海岛居民环境友好行为的影响因素,引导和鼓励海岛居民主动采取环境友好行为是改善海岛生态环境的有效途径。本研究在梳理国内外相关文献的基础上,对海岛居民环境友好行为的概念、类型及影响因素进行理论分析,建立包含生态管理行为、消费行为、说服行为、公民行为四个环境友好行为变量,环境态度、环境保护知识、环境经历、社会政策、行为约束五个影响因素变量在内的理论模型。结合海岛生态环境和海岛居民的特点,设计海岛居民版环境友好行为测量量表,并在长岛县进行问卷调查,运用描述性统计分析、结构方程模型分析探究海岛居民环境友好行为的影响因素及影响因素间的内在关系。研究发现:①海岛居民环境友好行为总体水平差异较大,难度较低的环境友好行为实施较好,而难度较高的实施较差;影响因素变量中,环境态度积极,环境经历丰富,环境保护知识掌握较好,相关社会政策较为不利,行为约束偏中性。②环境态度、环境经历、社会政策对海岛居民环境友好行为具有显著正向影响。③环境保护知识对环境态度具有显著正向影响,但对海岛居民环境友好行为无显著影响,存在“知易行难”现象。行为约束对海岛居民环境友好行为无显著影响。④环境经历不仅直接影响海岛居民环境友好行为,而且通过环境态度对海岛居民环境友好行为施加间接影响。基于研究结论,提出了改善海岛居民环境友好行为的对策建议。     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.     

武汉城市群夏季热岛特征及演变

利用2000~2010年共11期MODIS地表温度资料和多源多时相的遥感影像分类结果揭示武汉城市群的夏季热岛效应,反演并计算出10 a间武汉城市群日间和夜间的热岛强度变化、土地覆盖类型和城镇用地面积。在对不同时相的地表温度数据进行热岛指数归一化处理的基础上,分析了武汉城市群热岛的分布特征及年代演变,定量分析了武汉城市群以及中心城市武汉市不同热状况区面积的变化和热场的变迁。结果表明,武汉城市群夏季热岛效应较为明显,其中武汉市是主要热源和热中心;自2000年起,武汉城市群城乡温度差异逐步减小,热中心分布向外扩散,城市热岛区域急速扩张,整体热环境趋于恶化;新兴城区的开发增加了武汉市的热源分布,人工表面的增加以及自然表面的减少导致城市热岛效应不断加剧。